nerdyscout 7 months ago
parent
commit
dde927d754
  1. 15
      config-override
  2. 99
      config.txt
  3. 0
      on_boot.gcode

15
config-override

@ -1,15 +0,0 @@
; DO NOT EDIT THIS FILE
;Steps per unit:
M92 X40.00000 Y40.00000 Z110.00000
;Acceleration mm/sec^2:
M204 S1000.00000
;X- Junction Deviation, Z- Z junction deviation, S - Minimum Planner speed mm/sec:
M205 X0.05000 Z-1.00000 S0.00000
;Max cartesian feedrates in mm/sec:
M203 X500.00000 Y500.00000 Z5.00000 S-1.00000
;Max actuator feedrates in mm/sec:
M203.1 X500.00000 Y500.00000 Z5.00000
;WCS settings
G54
;Home offset (mm):
M206 X0.00000 Y0.00000 Z0.00000

99
config.txt

@ -56,29 +56,35 @@ second_usb_serial_enable true # This enables a s
# Hotend temperature control configuration
temperature_control.bed.enable true #
temperature_control.bed.thermistor_pin 0.24 #
temperature_control.bed.heater_pin 2.7 #
temperature_control.bed.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
temperature_control.bed.beta 4066 # or set the beta value
temperature_control.bed.set_m_code 140 #
temperature_control.bed.set_and_wait_m_code 190 #
temperature_control.bed.designator B #
temperature_control.bed.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
# Switch module for fan control
#temperature_control.bed.enable true #
#temperature_control.bed.thermistor_pin 0.24 #
#temperature_control.bed.heater_pin 2.7 #
#temperature_control.bed.thermistor EPCOS100K # see http://smoothieware.org/temperaturecontrol#toc5
#temperature_control.bed.beta 4066 # or set the beta value
#temperature_control.bed.set_m_code 140 #
#temperature_control.bed.set_and_wait_m_code 190 #
#temperature_control.bed.designator B #
#temperature_control.bed.max_pwm 64 # max pwm, 64 is a good value if driving a 12v resistor with 24v.
##################################################################
# Switch module
# https://smoothieware.org/switch
switch.relay1.enable false #
##################################################################
switch.relay1.enable true #
switch.relay1.input_on_command M106 #
switch.relay1.input_off_command M107 #
switch.relay1.output_pin 0.27^ #
switch.relay1.output_type digital # just on or off
switch.relay1.subcode 5
switch.relay1.output_pin 0.27 #
switch.relay1.output_type digital # just on or off
switch.relay2.enable false #
switch.relay2.input_on_command M42 #
switch.relay2.input_off_command M43 #
switch.relay2.output_pin 0.28^ #
switch.relay2.output_type digital # just on or off
switch.relay2.enable true #
switch.relay2.input_on_command M106 #
switch.relay2.input_off_command M107 #
switch.relay2.subcode 6
switch.relay2.output_pin 0.28 #
switch.relay2.output_type digital # just on or off
# automatically toggle a switch at a specified temperature. Different ones of these may be defined to monitor different temperatures and switch different swithxes
# useful to turn on a fan or water pump to cool the hotend
@ -89,9 +95,6 @@ switch.relay2.output_type digital # just on or off
#temperatureswitch.hotend.heatup_poll 15 # poll heatup at 15 sec intervals
#temperatureswitch.hotend.cooldown_poll 60 # poll cooldown at 60 sec intervals
# Switch module for spindle control
#switch.spindle.enable false #
##################################################################
# RE-ARM specific settings do not change
@ -106,44 +109,45 @@ network.enable false # enable the ether
dfu_enable true # enable dfu
panel.enable false # set to true to enable the panel code
#msd_disable false # disable the MSD (USB SDCARD) when set to true
#switch.spindle.enable false # Switch module for spindle control
return_error_on_unhandled_gcode false #
##################################################################
# VACUUM SENSING
# VACUUM SENSING - ok
##################################################################
# pump
# pump D8
switch.pump.enable true # Enable this module
switch.pump.input_on_command M106 # M280.1 S7.5 would be midway
switch.pump.input_off_command M107 # Same as M280.1 S0 0% duty cycle, effectively off
switch.pump.subcode 0
switch.pump.input_on_command M280 # M280.1 S7.5 would be midway
switch.pump.input_off_command M281 # Same as M280.1 S0 0% duty cycle, effectively off
#switch.pump.subcode 1
switch.pump.output_pin 2.7 # Must be a PWM capable pin
switch.pump.output_type pwm # H/W pwm output settable with S parameter in the input_on_command
switch.pump.output_type pwm # H/W pwm output settable with S parameter in the input_on_command
switch.pump.max_pwm 255 # Set max PWM for the pin default is 255
switch.pump.failsafe_set_to 0 # 0or 1 what to set the output pin to in case of a crash or HALT condition
# left solenoid
# left solenoid D9
switch.left.enable true # Enable this module
switch.left.input_on_command M106 # M280.1 S7.5 would be midway
switch.left.input_off_command M107 # Same as M280.1 S0 0% duty cycle, effectively off
switch.left.subcode 1
switch.left.output_pin 2.4 # Must be a PWM capable pin
switch.left.output_type digital # H/W pwm output settable with S parameter in the input_on_command
switch.left.failsafe_set_to 0 # 0 or 1 what to set the output pin to in case of a crash or HALT condition
#switch.left.output_on_command abort # this command is called when the switch changes to the ON state
#switch.left.output_off_command resume # This command is called when the switch changes to the OFF state
# right solenoid
switch.left.subcode 2
switch.left.output_pin 2.4! # Must be a PWM capable pin
switch.left.output_type digital # H/W pwm output settable with S parameter in the input_on_command
switch.left.failsafe_set_to 0 # 0 or 1 what to set the output pin to in case of a crash or HALT condition
#switch.left.output_on_command abort # this command is called when the switch changes to the ON state
#switch.left.output_off_command resume # This command is called when the switch changes to the OFF state
# right solenoid D10
# left solenoid
switch.right.enable true # Enable this module
switch.right.input_on_command M106 # M280.1 S7.5 would be midway
switch.right.input_off_command M107 # Same as M280.1 S0 0% duty cycle, effectively off
switch.right.subcode 2
switch.right.output_pin 2.5 # Must be a PWM capable pin
switch.right.subcode 3
switch.right.output_pin 2.5! # Must be a PWM capable pin
switch.right.output_type digital # H/W pwm output settable with S parameter in the input_on_command
switch.right.failsafe_set_to 0 # 0 or 1 what to set the output pin to in case of a crash or HALT condition
#switch.right.output_on_command abort # this command is called when the switch changes to the ON state
#switch.right.output_off_command resume # This command is called when the switch changes to the OFF state
switch.right.failsafe_set_to 0 # 0 or 1 what to set the output pin to in case of a crash or HALT condition
#switch.right.output_on_command abort # this command is called when the switch changes to the ON state
#switch.right.output_off_command resume # This command is called when the switch changes to the OFF state
##################################################################
@ -151,7 +155,6 @@ switch.right.failsafe_set_to 0 # 0 or 1 what to set the ou
##################################################################
return_error_on_unhandled_gcode false #
# Extruder module configuration
extruder.left.enable true # Whether to activate the extruder module at all. All configuration is ignored if false
extruder.left.steps_per_mm 150 # Steps per mm for extruder stepper
@ -159,8 +162,8 @@ extruder.left.default_feed_rate 600 # Default rate (
extruder.left.acceleration 500 # Acceleration for the stepper motor mm/sec²
extruder.left.max_speed 50 # mm/s
extruder.left.step_pin 2.0 # Pin for extruder step signal
extruder.left.dir_pin 0.5 # Pin for extruder dir signal
extruder.left.en_pin 0.4 # Pin for extruder enable signal
extruder.left.dir_pin 0.5 # Pin for extruder dir signal
extruder.left.en_pin 0.4 # Pin for extruder enable signal
extruder.left.x_offset 0 # x offset from origin in mm
extruder.left.y_offset 0 # y offset from origin in mm
extruder.left.z_offset 0 # z offset from origin in mm
@ -181,12 +184,12 @@ extruder.right.z_offset 0 # z offset from
##################################################################
# Endstops
# See http://smoothieware.org/endstops
##################################################################
# See http://smoothieware.org/endstops
endstops_enable true # The endstop module is enabled by default and can be disabled here
corexy_homing true # Set to true if homing on a hbot or corexy
#home_z_first true
home_z_first true
#Move_to_origin_after_home true
alpha_min_endstop 1.24^ # Pin to read min endstop, add a ! to invert if endstop is NO connected to ground
alpha_max_endstop 1.25^ # Pin to read max endstop, uncomment this and comment the above if using max endstops

0
sd_onboot.gcode → on_boot.gcode

Loading…
Cancel
Save